|Documents Home :: 4.2.6p3 :: drivers :: driver20.html
Reference ID: GPS
Driver ID: GPS_NMEA
Serial Port: /dev/gpsu; 4800 - 115200 bps, 8-bits, no parity
Serial Port: /dev/gpsppsu; for just the PPS signal (this is tried first for PPS, before /dev/gpsu)
Serial Port: /dev/gpsu; symlink to server:port (for nmead) Features: tty_clk
This driver supports GPS receivers with the $GPRMC, $GPGLL, $GPGGA, $GPZDA, and $GPZDG NMEA sentences by default. Note that Accord's custom NMEA sentence $GPZDG reports using the GPS timescale, while the rest of the sentences report UTC. The difference between the two is a whole number of seconds which increases with each leap second insertion in UTC. To avoid problems mixing UTC and GPS timescales, the driver disables processing of UTC sentences once $GPZDG is received.
The driver expects the receiver to be set up to transmit at least one supported sentence every second.
The accuracy depends on the receiver used. Inexpensive GPS models are available with a claimed PPS signal accuracy of 1 ms or better relative to the broadcast signal. However, in most cases the actual accuracy is limited by the precision of the timecode and the latencies of the serial interface and operating system.
If the Operating System supports PPSAPI (RFC 2783), fudge flag1 1 enables its use.
The various GPS sentences that this driver recognises look like this:
(others quietly ignored)
$GPRMC,UTC,POS_STAT,LAT,LAT_REF,LON,LON_REF,SPD,HDG,DATE,MAG_VAR,MAG_REF*CS<cr><lf> $GPGLL,LAT,LAT_REF,LONG,LONG_REF,UTC,POS_STAT*CS<cr><lf> $GPGGA,UTC,LAT,LAT_REF,LONG,LONG_REF,FIX_MODE,SAT_USED,HDOP,ALT,ALT_UNIT,GEO,G_UNIT,D_AGE,D_REF*CS<cr><lf> $GPZDA,UTC,DD,MM,YYYY,TH,TM,*CS<cr><lf> $GPZDG,GPSTIME,DD,MM,YYYY,AA.BB,V*CS<cr><lf> UTC - Time of day on UTC timescale. Hours, minutes and seconds [fraction (opt.)]. (hhmmss[.fff]) POS_STAT - Position status. (A = Data valid, V = Data invalid) LAT - Latitude (llll.ll) LAT_REF - Latitude direction. (N = North, S = South) LON - Longitude (yyyyy.yy) LON_REF - Longitude direction (E = East, W = West) SPD - Speed over ground. (knots) (x.x) HDG - Heading/track made good (degrees True) (x.x) DATE - Date (ddmmyy) MAG_VAR - Magnetic variation (degrees) (x.x) MAG_REF - Magnetic variation (E = East, W = West) FIX_MODE - Position Fix Mode (0 = Invalid, >0 = Valid) SAT_USED - Number Satellites used in solution HDOP - Horizontal Dilution of Precision ALT - Antenna Altitude ALT_UNIT - Altitude Units (Metres/Feet) GEO - Geoid/Elipsoid separation G_UNIT - Geoid units (M/F) D_AGE - Age of last DGPS Fix D_REF - Reference ID of DGPS station GPSTIME - Time of day on GPS timescale. Hours, minutes and seconds [fraction (opt.)]. (hhmmss[.f]) DD - Day of the month (1-31) MM - Month of the year (1-12) YYYY - Year AA.BB - Denotes the signal strength (should be < 05.00) V - GPS sync status '0' => INVALID time, '1' => accuracy of +/- 20ms, '2' => accuracy of +/- 100ns CS - Checksum <cr><lf> - Sentence terminator.
Specific GPS sentences and bitrates may be selected by setting bits of the 'mode' in the server configuration line:
server 127.127.20.x mode X
bit 0 - process $GPMRC (value = 1)
bit 1 - process $GPGGA (value = 2)
bit 2 - process $GPGLL (value = 4)
bit 4 - process $GPZDA or $GPZDG (value = 8)
The default (mode 0) is to process all supported sentences, which results in the last received each cycle being used. Multiple sentences may be selected by adding their mode bit values. The driver uses 4800 bits per second by default. Faster bitrates can be selected using bits 4, 5, and 6 of the mode field:
bits 4/5/6 - select serial bitrate (0 for 4800 - the default, 16 for 9600, 32 for 19200, 48 for 38400, 64 for 57600, 80 for 115200)
The driver will send a $PMOTG,RMC,0000*1D<cr><lf> command each poll interval. This is not needed on most GPS receivers because they automatically send $GPRMC every second, but helps a Motorola GPS receiver that is otherwise silent. NMEA devices ignore commands they do not understand.
Now switch only $GPRMC on by sending it the following string.
On some systems the PPS signal isn't switched on by default. It can be switched on by sending the following string.
The GPS sentence that is used is written to the clockstats file and available with ntpq -c clockvar.
Reference Clock Drivers