Access Control Options
from Pogo, Walt Kelly
The skunk watches for intruders and sprays.
Table of Contents
Access Control Support
The ntpd daemon implements a general purpose access control list
(ACL) containing address/match entries sorted first by increasing address
values and then by increasing mask values. A match occurs when the bitwise
AND of the mask and the packet source address is equal to the bitwise AND of
the mask and address in the list. The list is searched in order with the last
match found defining the restriction flags associated with the entry.
An example may clarify how it works. Our campus has two class-B networks,
128.4 for the ECE and CIS departments and 128.175 for the rest of campus.
Let's assume (not true!) that subnet 128.4.1 homes critical services like class
rosters and spread sheets. A suitable ACL might be
restrict default nopeer # deny new associations
restrict 18.104.22.168 mask 255.255.0.0 # allow campus access
restrict 22.214.171.124 mask 255.255.0.0 none # allow ECE and CIS access
restrict 126.96.36.199 mask 255.255.255.0 notrust # require authentication on subnet 1
restrict time.nist.gov # allow access
While this facility may be useful for keeping unwanted, broken or malicious clients from congesting innocent servers, it should not be considered an alternative to the NTP authentication facilities. Source address based restrictions are easily circumvented by a determined cracker.
Access Control Commands
- discard [ average avg ][ minimum min ] [ monitor prob ]
- Set the parameters of the rate control facility which protects the server
from client abuse. If the limited flag is present in the ACL, packets
that violate these limits are discarded. If in addition the kod restriction
is present, a kiss-o'-death packet is returned.
- average avg
- Specify the minimum average interpacket spacing (minimum average headway
time) in log2 s with default 3.
- minimum min
- Specify the minimum interpacket spacing (guard time) in log2 s
with default 1.
- Specify the probability of discard for packets that overflow the rate-control
window. This is a performance optimization for servers with aggregate arrivals
of 1000 packets per second or more.
- restrict address [mask mask] [flag][...]
- The address argument expressed in dotted-quad form is the
address of a host or network. Alternatively, the address argument
can be a valid host DNS name. The mask argument expressed in
dotted-quad form defaults to 255.255.255.255, meaning that the address is
treated as the address of an individual host. A default entry (address 0.0.0.0,
mask 0.0.0.0) is always included and is always the first entry in the list.
Note that the text string default, with no mask option, may be used
to indicate the default entry.
- Some flags have the effect to deny service, some have the effect to
enable service and some are conditioned by other flags. The flags. are
not orthogonal, in that more restrictive flags will often make less restrictive
ones redundant. The flags that deny service are classed in two categories,
those that restrict time service and those that restrict informational queries
and attempts to do run-time reconfiguration of the server. One or more of the
following flags may be specified:
- Discard received NTP packets with probability 0.1; that is, on average drop
one packet in ten. This is for testing and amusement. The name comes from Bob
Braden's flakeway, which once did a similar thing for early Internet
- Deny packets of all kinds, including ntpq and ntpdc queries.
- Send a kiss-o'-death (KoD) packet if the limited flag is present
and a packet violates the rate limits established by the discard command.
KoD packets are themselves rate limited for each source address separately.
If this flag is not present, packets that violate the rate limits are discarded.
- Deny time service if the packet violates the rate limits established by the discard command.
This does not apply to ntpq and ntpdc queries.
- Declare traps set by matching hosts to be low priority. The number of traps
a server can maintain is limited (the current limit is 3). Traps are usually
assigned on a first come, first served basis, with later trap requestors being
denied service. This flag modifies the assignment algorithm by allowing low
priority traps to be overridden by later requests for normal priority traps.
- Enable Microsoft Windows MS-SNTP authentication using Active Directory services.
Note: Potential users should be aware that these services
involve a TCP connection to another process that could potentially block,
denying services to other users. Therefore, this flag should be used only
for a dedicated server with no clients other than MS-SNTP.
- Deny ntpq and ntpdc queries which attempt to modify the
state of the server (i.e., run time reconfiguration). Queries which return information
- Deny ntpq and ntpdc queries. Time service is not affected.
- Deny packets that might mobilize an association unless authenticated. This
includes broadcast, symmetric-active and manycast server packets when a configured
association does not exist. Note that this flag does not apply to packets
that do not attempt to mobilize an association.
- Deny all packets except ntpq and ntpdc queries.
- Decline to provide mode 6 control message trap service to matching hosts.
The trap service is a subsystem of the ntpdc control message protocol
which is intended for use by remote event logging programs.
- Deny packets that are not cryptographically authenticated. Note carefully
how this flag interacts with the auth option of the enable and disable commands.
If auth is enabled, which is the default, authentication is required
for all packets that might mobilize an association.
If auth is
disabled, but the notrust flag is not present, an association can be
mobilized whether or not authenticated. If auth is disabled, but the notrust flag
is present, authentication is required only for the specified address/mask
- This is actually a match algorithm modifier, rather than a restriction
flag. Its presence causes the restriction entry to be matched only if the
source port in the packet is the standard NTP UDP port (123). Both ntpport and non-ntpport may
be specified. The ntpport is considered more specific and is sorted
later in the list.
- Deny packets that do not match the current NTP version.
- Default restriction list entries with the flags ignore, ntpport,
for each of the local host's interface addresses are inserted into the table
at startup to prevent the server from attempting to synchronize to its own time.
A default entry is also always present, though if it is otherwise unconfigured;
no flags are associated with the default entry (i.e., everything besides your
own NTP server is unrestricted).