|Documents Home :: 4.2.6p4 :: prefer.html
Listen carefully to what I say; it is very complicated.
Last update: 22-Apr-2009 14:04 UTC
This page summarizes the criteria for choosing from among a number of potential sources suitable contributors to the clock discipline algorithm. The criteria are very meticulous, since they have to handle many different scenarios that may be optimized for peculiar circumstances, including some scenarios designed to support planetary and deep space missions.
Recall the suite of NTP data acquisition and grooming algorithms as these algorithms proceed in five phases. Phase one discovers the available sources and mobilizes an association for each candidate found. These candidates can result from explicit configuration, broadcast discovery or the pool and manycast autonomous configuration schemes. Phase two grooms the selectable candidates excluding those sources showing one or more of the following errors
Phase three uses an intersection algorithm to select the truechimers from among the candidates, leaving behind the falsetickers. A server or peer configured with the true option is ipso facto a truechimer independent of this algorithm. Phase four uses a clustering algorithm to cast off statistical outliers from the truechimers until a set of survivors not less than the number specified as the minclock option of the tos command, with default 3. Phase five uses a set of mitigation rules to select from among the survivors a system peer from which a set of system statistics can be inherited and passed along to a dependent client population. The clock offset developed from these algorithms can discipline the system clock either using the ntpd clock discipline algorithm or enable the kernel to discipline the system clock directly, as described on the A Kernel Model for Precision Timekeeping page. Phase five is the topic of this page.
The behavior of the various algorithms and mitigation rules involved depends on how the various synchronization sources are classified. This depends on whether the source is local or remote and if local the type of source. The following classes are defined:
The mitigation rules are designed to provide an intelligent selection of the system peer from among the survivors of different types. When used with the server or peer commands, the prefer option designates one or more survivors as preferred over all others. While the rules do not forbid it, it is usually not useful to designate more than one source as preferred; however, if more than one source is so designated, they are used in the order specified in the configuration file; that is, if the first one becomes unselectable, the second one is considered and so forth. This order of priority is also applicable to multiple PPS drivers, multiple modem drivers and even multiple local drivers, although that would not normally be useful.
The clustering algorithm works on the set of truechimers produced by the intersection algorithms. Ordinarily, any one of them can in principle provide correct time; however, due to various latency variations, not all can provide the most accurate and stable time. The clustering algorithm, processes the truechimers in one or more rounds to cast off a statistical outlier until no more than the minclock option of the tos command are left. The default for this option is 3.
In the prefer scheme the clustering algorithm is modified so that the prefer peer is never discarded; on the contrary, its potential removal becomes a rounds-termination condition. However, the prefer peer can still be discarded by the intersection algorithm as a falseticker. To avoid this, it is usually wise to increase the mindist option of the tos command from the default .005 s to something like .05 s.
Ordinarily, the combining algorithm computes a weighted average of the survivor offsets to produce the final synchronization source. However, if a prefer peer is among the survivors, the combining algorithm is not used. Instead, the offset of the prefer peer is used exclusively as the final synchronization source. In the common case involving a radio clock and a flock of remote backup servers, and with the radio clock designated a prefer peer, the result is that the radio clock normally disciplines the system clock as long as the radio itself remains operational. However, if the radio fails or becomes a falseticker, the averaged backup sources continue to discipline the system clock.
As the selection algorithm scans the associations for selectable candidates, the modem driver and local driver are segregated for later, but only if not designated a prefer peer. If so designated, a driver is included among the candidate population. In addition, if orphan parents are found the parent with the lowest metric is segregated for later; the others are discarded. For this purpose the metric is defined as the four-octet IPv4 address or the first four octets of the hashed IPv6 address. The resulting candidates, including any prefer peers found, are processed by the intersection to produce a possibly empty set of truechimers. The clustering algorithm ranks the truechimers first by stratum then by synchronization distance and designates the survivor with the lowest distance as the potential system peer.
If one or more truechimers support a pulse-per-second (PPS) signal and the PPS signal is operating correctly, it is designated a PPS driver. If more than one PPS diver are found, only the first one is used. The PPS driver is not included in the combining algorithm and is mitigated separately.
At this point we have the following contributors to the system clock discipline:
The mitigation algorithm proceeds in three steps in turn.
If none of the above is the case, the data are disregarded and the system variables remain as they are.
The minsane option of the tos command, the prefer option of the server and peer commands and the flag options of the fudge command for the PPS driver can be used with the mitigation rules to provide many useful configurations. The minsane option specifies the minimum number of survivors required to synchronized the system clock. The prefer option designates the prefer peer. The driver-dependent flag options enable the PPS driver for various conditions.
A common scenario is a GPS driver with a serial timecode and PPS signal. The PPS signal is disabled until the system clock has been set by some means, not necessarily the GPS driver. If the serial timecode is within 0.4 s of the PPS signal, the GPS driver is designated the PPS driver and the PPS signal disciplines the system clock. If no GPS satellites are in view, or if the PPS signal is disconnected, the GPS driver stops updating the system clock and so eventually becomes unreachable and replaced by other sources..
Whether or not the GPS driver disables the PPS signal when unreachable is at the discretion of the driver. Ordinarily, the PPS signal would be disabled in this case; however, When the GPS receiver has a precision holdover oscillator, the driver may elect to continue PPS operation. In this case the PPS signal continues to discipline the system clock.