|Documents Home :: 4.2.8p14 :: prefer.html
Listen carefully to what I say; it is very complicated.
Last update: 10-Mar-2014 05:18 UTC
This page summarizes the criteria for choosing from among the survivors of the clock cluster algorithm a set of contributors to the clock discipline algorithm. The criteria are very meticulous, since they have to handle many different scenarios that may be optimized for special circumstances, including some scenarios designed to support planetary and deep space missions. For additional information on statistical principles and performance metrics, see the Performance Metrics page.
Recall the suite of NTP data acquisition and grooming algorithms. These algorithms proceed in five phases. Phase one discovers the available sources and mobilizes an association for each source found. These sources can result from explicit configuration, broadcast discovery or the pool and manycast autonomous configuration schemes. See the Automatic Server Discovery Schemes page for further information.
Phase two selects the candidates from among the sources by excluding those sources showing one or more of the errors summarized on the Clock Select Algorithm page and to determine the truechimers from among the candidates, leaving behind the falsetickers. A server or peer configured with the true option is declared a truechimer independent of this algorithm. Phase four uses the algorithm described on the Clock Cluster Algorithm page to prune the statistical outliers from the truechimers, leaving the survivor list as result.
Phase five uses a set of algorithms and mitigation rules to combined the survivor statistics and discipline the system clock. The mitigation rules select from among the survivors a system peer from which a set of system statistics can be inherited and passed along to dependent clients, if any. The mitigation algorithms and rules are the main topic of this page. The clock offset developed from these algorithms can discipline the system clock, either using the clock discipline algorithm or using the kernel to discipline the system clock directly, as described on the A Kernel Model for Precision Timekeeping page.
The clock combine algorithm uses the survivor list to produce a weighted average of both offset and jitter. Absent other considerations discussed later, the combined offset is used to discipline the system clock, while the combined jitter is augmented with other components to produce the system jitter statistic inherited by dependent clients, if any.
The clock combine algorithm uses a weight factor for each survivor equal to the reciprocal of the root distance. This is normalized so that the sum of the reciprocals is equal to unity. This design favors the survivors at the smallest root distance and thus the smallest maximum error.
The anti-clockhop algorithm is intended for cases where multiple servers are available on a fast LAN with modern computers. Typical offset differences between servers in such cases are less than 0.5 ms. However, changes between servers can result in unnecessary system jitter. The object of the anti-clockhop algorithm is to avoid changing the current system peer, unless it becomes stale or has significant offset relative to other candidates on the survivor list.
For the purposes of the following description, call the last selected system peer the old peer, and the currently selected source the candidate peer. At each update, the candidate peer is selected as the first peer on the survivor list sorted by increasing root distance. The algorithm initializes the -clockhop threshold with the value of mindist, by default 1 ms.
The anti-clockhop algorithm is called immediately after the combine algorithm. If there was no old peer or the old and candidate peers are the same, the candidate peer becomes the system peer. If the old peer and the candidate peer are different, the algorithm measures the difference between the offset of the old peer and the candidate peer. If the difference exceeds the clockhop threshold, the candidate peer becomes the system peer and the clockhop threshold is restored to its original value. If the difference is less than the clockhop threshold, the old peer continues as the system peer. However, at each subsequent update, the algorithm reduces the clockhop threshold by half. Should operation continue in this way, the candidate peer will eventually become the system peer.
The behavior of the various algorithms and mitigation rules involved depends on how the various synchronization sources are classified. This depends on whether the source is local or remote and if local, the type of source. The following classes are defined:
The mitigation rules are designed to provide an intelligent selection of the system peer from among the selectable sources of different types. When used with the server or peer commands, the prefer option designates one or more sources as preferred over all others. While the rules do not forbid it, it is usually not useful to designate more than one source as preferred; however, if more than one source is so designated, they are used in the order specified in the configuration file. If the first one becomes un selectable, the second one is considered and so forth. This order of priority is also applicable to multiple PPS drivers, multiple modem drivers and even multiple local drivers, although that would not normally be useful.
The cluster algorithm works on the set of truechimers produced by the select algorithm. At each round the algorithm casts off the survivor least likely to influence the choice of system peer. If selectable, the prefer peer is never discarded; on the contrary, its potential removal becomes a termination condition. However, the prefer peer can still be discarded by the select algorithm as a falseticker; otherwise, the prefer peer becomes the system peer.
Ordinarily, the combine algorithm computes a weighted average of the survivor offset and jitter to produce the final values. However, if a prefer peer is among the survivors, the combine algorithm is not used. Instead, the offset and jitter of the prefer peer are used exclusively as the final values. In the common case involving a radio clock and a flock of remote backup servers, and with the radio clock designated a prefer peer, the the radio clock disciplines the system clock as long as the radio itself remains operational. However, if the radio fails or becomes a falseticker, the combined backup sources continue to discipline the system clock.
As the select algorithm scans the associations for selectable candidates, the modem driver and local driver are segregated for later, but only if not designated a prefer peer. If so designated, the driver is included among the candidate population. In addition, if orphan parents are found, the parent with the lowest metric is segregated for later; the others are discarded. For this purpose the metric is defined as the four-octet IPv4 address or the first four octets of the hashed IPv6 address. The resulting candidates, including any prefer peers found, are processed by the select algorithm to produce a possibly empty set of truechimers.
As previously noted, the cluster algorithm casts out outliers, leaving the survivor list for later processing. The survivor list is then sorted by increasing root distance and the first entry temporarily designated the system peer. At this point the following contributors to the system clock discipline may be available:
The mitigation algorithm proceeds in three steps in turn.
If none of the above is the case, the data are disregarded and the system variables remain as they are.
The minsane option of the tos command, the prefer option of the server and peer commands and the flag option of the fudge command for a selected driver can be used with the mitigation rules to provide many useful configurations. The minsane option specifies the minimum number of survivors required to synchronize the system clock. The prefer option operates as described in previous sections. The flag option enables the PPS signal for the selected driver.
A common scenario is a GPS driver with a serial timecode and PPS signal. The PPS signal is disabled until the system clock has been set by some means, not necessarily the GPS driver. If the serial timecode is within 0.4 s of the PPS signal, the GPS driver is designated the PPS driver and the PPS signal disciplines the system clock. If the serial timecode becomes unreliable, or if the PPS signal is disconnected, the GPS driver stops updating the system clock and so eventually becomes unreachable and is replaced by other sources.
Whether or not the GPS driver disables the PPS signal when the timecode becomes unreliable is at the discretion of the driver. Ordinarily, the PPS signal is disabled in this case; however, when the GPS receiver has a precision holdover oscillator, the driver may elect to continue PPS discipline . In this case, minsane can be set to zero so the PPS signal continues to discipline the system clock.