|Documents Home :: current-stable :: clock.html
Last update: 4-Aug-2011 23:40 UTC
In the NTPv4 specification and reference implementation a state machine is used to manage the system clock under exceptional conditions, as when the daemon is first started or when encountering severe network congestion. This page describes the design and operation of the state machine in detail.
The state machine is activated upon receipt of an update by the clock discipline algorithm. its primary purpose is to determines whether the clock is slewed or stepped and how the initial time and frequency are determined using three thresholds: panic, step and stepout, and one timer: hold.
Most computers today incorporate a time-of-year (TOY) chip to maintain the time when the power is off. When the computer is restarted, the chip is used to initialize the operating system time. In case there is no TOY chip or the TOY time is different from NTP time by more than the panic threshold, the daemon assumes something must be terribly wrong, so exits with a message to the system operator to set the time manually. With the -g option on the command line, the daemon sets the clock to NTP time at the first update, but exits if the offset exceeds the panic threshold at subsequent updates. The panic threshold default is 1000 s, but it can be changed with the panic option of the tinker command.
Under ordinary conditions, the clock discipline gradually slews the clock to the correct time, so that the time is effectively continuous and never stepped forward or backward. If, due to extreme network congestion, an offset spike exceeds the step threshold, by default 128 ms, the spike is discarded. However, if offset spikes greater than the step threshold persist for an interval more than the stepout threshold, by default 300 s, the system clock is stepped to the correct time.
In practice, the need for a step has been extremely rare and almost always the result of a hardware failure or operator error. The step threshold and stepout threshold can be changed using the step and stepout options of the tinker command, respectively. If the step threshold is set to zero, the step function is entirely disabled and the clock is always slewed. The daemon sets the step threshold to 600 s using the -x option on the command line. If the -g option is used or the step threshold is set greater than 0.5 s, the precision time kernel support is disabled.
Historically, the most important application of the step function was when a leap second was inserted in the Coordinated Universal Time (UTC) timescale and the kernel precision time support was not available. This also happened with older reference clocks that indicated an impending leap second, but the radio itself did not respond until it resynchronized some minutes later. Further details are on the Leap Second Processing page.
In some applications the clock can never be set backward, even it accidentally set forward a week by some evil means. The issues should be carefully considered before using these options. The slew rate is fixed at 500 parts-per-million (PPM) by the Unix kernel. As a result, the clock can take 33 minutes to amortize each second the clock is outside the acceptable range. During this interval the clock will not be consistent with any other network clock and the system cannot be used for distributed applications that require correctly synchronized network time.
When the daemon is started after a considerable downtime, it could be the TOY chip clock has drifted significantly from NTP time. This can cause a transient at system startup. In the past, this has produced a phase transient and resulted in a frequency surge that could take some time, even hours, to subside. When the highest accuracy is required, some means is necessary to manage the startup process so that the the clock is quickly set correctly and the frequency is undisturbed. The hold timer is used to suppress frequency adjustments during the training and startup intervals described below. At the beginning of the interval the hold timer is set to the stepout threshold and decrements at one second intervals until reaching zero. However, the hold timer is forced to zero if the residual clock offset is less than 0.5 ms. When nonzero, the discipline algorithm uses a small time constant (equivalent to a poll exponent of 2), but does not adjust the frequency. Assuming that the frequency has been set to within 1 PPM, either from the frequency file or by the training interval described later, the clock is set to within 0.5 ms in less than 300 s.
The state machine operates in one of four nonoverlapping intervals.
The state machine consists of five states. An event is created when an update is received by the discipline algorithm. Depending on the state and the the offset magnitude, the machine performs some actions and transitions to the same or another state. Following is a short description of the states.